水草情迷

我都用過此co2溶解器(於e-shop van 到買,外表同你第一個post的一樣),的確溶解更有效率及可以節省co2用量,外接時又可美觀及鏘位,缺點為當co2關左時水會慢慢滲入co2果層,令到內層生銹而減低效率,加上又不能清洗.另外此co2溶解器需要用更大的氣壓才能令co2穿透"滲透層"進入水中,令我有兩個BioPlast的膠計泡器先後因承受不住而爆左,(我用BioPlast溶解器細錶set 0.3-0.4 bar,而用該co2溶解器則為 2 bar以上才可以有每秒1泡)
以上為本人使用的經歷,僅供參考.

Ken: How much is your van co2溶解器? can you remember? Please PM me if you do not want to disclose here. I hope my co2溶解器 is not too expensive.

They said co2溶解器 will not 生銹 (see DSC01287a.jpg). I hope it will not 生銹 in the long run, since I will connect it to my tank tonight.

Copy from other TW website "這東東的原理，其實就是應用「粉末冶金」的技術。 簡單點說，就是將不鏽鋼粉末（stainless powder）以高溫高壓燒結而成，調控其製程參數，可以使得燒結起來的成品具有幾近無窮多個小孔，而每個孔也會十分的小。 用在水族上當以高壓將氣體壓到溶解器時，便會經過小孔而達成「細化」效果，經由水在管道中的流動，才將二氧化碳溶解的"

Therefore it is easy to understand that when there is not CO2 supply, CO2 pressure drop and water flow back to CO2果層 thought 不鏽鋼層. Actually I am now using 老通的 for two months. Seems also no 生銹. Let me recheck the 老通的溶解器 to see any 銹. I will picture it latter today.

I am using a simple glass 計泡器 also bought from 老通....$2x to 3x cannot remember. I also saw it in 卡x at FS.

Actually I am using DIY 2L cola coca bottle, pressure seems not too high and the result seems very good. Since I am using DIY so cannot check the pressure.
see [貼圖]我的鹿角苔飛船準備升空

Other links for your reference:
有人用過這個外置CO2擴散器嗎？
多功能co2溶解器!!!


P.S. I tried hard to search for the 多功能co2溶解器 and just want to share and discuss my experence here. (非宣傳). I am not try to sell any 多功能co2溶解器 here.

我都係用van記已有兩年,我最近都有咁o既情況出現,出氣慢o左,個樽叉o左一星期倒,以要個扭到最大,都係每秒兩至三個泡,可能真係塞o左,而至於個不銹鋼膽都會生銹的,只不過是無咁易生銹,以家都唔知點好

Clogging problem:

Will it be better if the diffuser is connected to the water OUTlet instead of intake? The water that passes through will be cleaner which has a lower chance to block the fine mesh.
Also solves the problem with the nitrifying bacteria!

上星期我在花地灣見到, 標價65人仔, 我沒有買.

It is the same?........
I 買貴o左???



Additional Information:

PuppyHawk:
我那個不是被水中的雜物或垃圾塞住,而是內層表面生銹令其減低效率!

Ken兄,我之前都有提過同你差唔多o既情況,但我將佢拆o左出黎,用洗奶樽刷(一set有兩個,一大一細),用細果個通o下佢,以家又回復正常喇!

I also find bolckage at 內層表面. But it is not due to 生銹 .......is by some jelly like stuff and also use 用洗奶樽刷 to clean it.

I think that the 臺灣的co2溶解器 that I post here is the same one as Van's co2溶解器. Because I have seen his photo album in 水草情迷 after I bought my 臺灣的co2溶解器.

How much is the "洗奶樽刷"?

好.....好似十幾皮倒la

1a.jpg....如將出氣口接上濾筒入水處...加長CO2在水中溶解時間...效果我想會更佳...

係呀好多前輩高人都是將CO 2 溶解器接在入濾筒前的

_________________
你一天中僅有這麼多個小時，你只能在這個時間內努力工作，那麼為甚麼為錢而拚命工作呢？是不是應該學會讓錢和別人為你工作？這樣你才能夠自由自在地去做其他重要的事情。

Just worry that the dirty water will clog the diffuser mesh if you connect it to the water intake

D 圖的接駁方式都係駁係入水喉, 如果駁係入水口,
咁做咪同 '放個玻璃擴散器在入水口下面' 差唔多???

所以我懷疑佢如果唔經濾桶, 改為駁在出水喉的溶解能力會大減..

請問是否主要靠濾桶溶解 CO2的呢?